논문 상세보기

한국전기전자재료학회> 전기전자재료학회논문지(J. Korean Inst. Electr. Electron. Mater. Eng.)> DLC 박막이 코팅된 폴리머 애자의 표면 및 물리적 특성

KCI등재

DLC 박막이 코팅된 폴리머 애자의 표면 및 물리적 특성

Surface and Physical Properties of Polymer Insulator Coated with Diamond-Like Carbon Thin Film

김영곤 ( Young Gon Kim ) , 박용섭 ( Yong Seob Park )
  • : 한국전기전자재료학회
  • : 전기전자재료학회논문지(J. Korean Inst. Electr. Electron. Mater. Eng.) 34권1호
  • : 연속간행물
  • : 2021년 01월
  • : 16-20(5pages)
전기전자재료학회논문지(J. Korean Inst. Electr. Electron. Mater. Eng.)

DOI


목차

1. 서 론
2. 실험 방법
3. 결과 및 고찰
4. 결 론
ORCID
REFERENCES

키워드 보기


초록 보기

In this study, we tried finding new materials to improve the stain resistance properties of polymer insulating materials. Using the filtered vacuum arc source (FVAS) with a graphite target source, DLC thin films were deposited on silicon and polymer insulator substrates depending on their thickness to confirm the surface properties, physical properties, and structural properties of the thin films. Subsequently, the possibility of using a DLC thin film as a protective coating material for polymer insulators was confirmed. DLC thin films manufactured in accordance with the thickness of various thin films exhibited a very smooth and uniform surface. As the thin film thickness increased, the surface roughness value decreased and the contact angle value increased. In addition, the elastic modulus and hardness of the DLC thin film slightly increased, and the maximum values of elastic modulus and hardness were 214.5 GPa and 19.8 GPa, respectively. In addition, the DLC thin film showed a very low leakage current value, thereby exhibiting electrical insulation properties.

UCI(KEPA)

간행물정보

  • : 공학분야  > 전기공학
  • : KCI등재
  • :
  • : 격월
  • : 1226-7945
  • : 2288-3258
  • : 학술지
  • : 연속간행물
  • : 1988-2021
  • : 4586


저작권 안내

한국학술정보㈜의 모든 학술 자료는 각 학회 및 기관과 저작권 계약을 통해 제공하고 있습니다.

이에 본 자료를 상업적 이용, 무단 배포 등 불법적으로 이용할 시에는 저작권법 및 관계법령에 따른 책임을 질 수 있습니다.

34권6호(2021년 11월) 수록논문
최근 권호 논문
| | | |

KCI등재

1제일원리 계산을 활용한 전기화학 촉매 연구

저자 : 김동연 ( Dong Yeon Kim )

발행기관 : 한국전기전자재료학회 간행물 : 전기전자재료학회논문지(J. Korean Inst. Electr. Electron. Mater. Eng.) 34권 6호 발행 연도 : 2021 페이지 : pp. 393-400 (8 pages)

다운로드

(기관인증 필요)

초록보기

As the recent climate problems are getting worse year after year, the demands for clean energy materials have highly increased in modern society. However, the candidate material classes for clean energy expand rapidly and the outcomes are too complex to be interpreted at laboratory scale (e.g., multicomponent materials). In order to overcome these issues, the firstprinciples calculations are becoming attractive in the field of material science. The calculations can be performed rapidly using virtual environments without physical limitations in a vast candidate pool, and theory can address the origin of activity through the calculations of electronic structure of materials, even if the structure of material is too complex. Therefore, in terms of the latest trends, we report academic progress related to the first-principles calculations for design of efficient electrocatalysts. The basic background for theory and specific research examples are reported together with the perspective on the design of novel materials using first-principles calculations.

KCI등재

2자성 액추에이터 기반의 소프트 로봇

저자 : 노규령 ( Gyu-Lyeong Nor ) , 최문기 ( Moon Kee Choi )

발행기관 : 한국전기전자재료학회 간행물 : 전기전자재료학회논문지(J. Korean Inst. Electr. Electron. Mater. Eng.) 34권 6호 발행 연도 : 2021 페이지 : pp. 401-415 (15 pages)

다운로드

(기관인증 필요)

초록보기

Soft robots are promising devices for applications in drug delivery, sensing, and manufacturing. Traditional hard robotics are manufactured with rigid materials and their degrees of motion are constrained by the orientation of the joints. In contrast to rigid counterpart, soft robotics, employing soft and stretchable materials that easily deforms in shape, can realize complex motions (i.e., locomotion, swimming, and grappling) with a simple structure, and easily adapt to dynamic environment. Among them, the magnetic actuators exhibit unique characteristics such as rapid and accurate motion control, biocompatibility, and facile remote controllability, which make them promising candidates for the next-generation soft robots. Especially, the magnetic actuators instantly response to the stimuli, and show no-hysteresis during the recovery process, essential for continuous motion control. Here, we present the state-of-the-art fabrication process of magnetically controllable nano-/micro-composites, magnetically aligning process of the composites, and 1-dimensional/multi-dimensional multimodal motion control for the next-generation soft actuators.

KCI등재

3COMSOL Multiphysics를 활용한 캔틸레버 형태의 압전 에너지 하베스터 구조 해석 시뮬레이션

저자 : 곽민섭 ( Min Sub Kwak ) , 황건태 ( Geon-tae Hwang )

발행기관 : 한국전기전자재료학회 간행물 : 전기전자재료학회논문지(J. Korean Inst. Electr. Electron. Mater. Eng.) 34권 6호 발행 연도 : 2021 페이지 : pp. 416-425 (10 pages)

다운로드

(기관인증 필요)

초록보기

In the 4th industrial age, electronic devices are becoming smaller and lighter with a low power consumption to overcome spatial limitation. The piezoelectric energy harvesters can convert mechanical kinetic energy into electric energy; thus, enabling the operation of small electronic devices. Recently, various piezoelectric harvesters have been reported and the electric output from these harvesters could be anticipated by theoretical analysis methods. For example, COMSOL Multiphysics software provides a theoretical simulation of piezoelectric effect with a combination of mechanical and electrical phenomena in the piezoelectric materials. This article introduces a brief modeling of piezoelectric harvester to investigate mechanical stress and electrical output of harvesting devices by the COMSOL Multiphysics software.

KCI등재

4열경화성 에폭시를 이용한 가스 절연 개폐기용 절연 스페이서의 사출 성형 최적화 시뮬레이션

저자 : 배재성 ( Jaesung Bae ) , 이원창 ( Wonchang Lee ) , 지홍섭 ( Hongsub Jee ) , 홍병유 ( Byungyou Hong ) , 이재형 ( Jaehyeong Lee )

발행기관 : 한국전기전자재료학회 간행물 : 전기전자재료학회논문지(J. Korean Inst. Electr. Electron. Mater. Eng.) 34권 6호 발행 연도 : 2021 페이지 : pp. 426-432 (7 pages)

다운로드

(기관인증 필요)

초록보기

Injection molding is used in many industrial fields such as home appliances, vehicle parts, and electronic device parts because various resins can be molded, leading to mass production of complex shapes. Generally, the empirical prediction method is used to set the initial processing conditions of injection molding. However, this approach requires a lot of cost and its presented solution is not accurate. In this paper, injection molding was simulated through the MoldflowTM in order to manufacture the spacer for gas insulated switch. Through the simulation, the flow of the resin with respect to the diameter of the inlet was analyzed. It was found that the process was possible at a higher resin temperature as the diameter of the inlet increased. In addition, through thermal analysis during injection of the resin, it was confirmed that a stagnation phenomenon occurred at the insert portion during injection molding, and the temperature of the resin was higher than that of the mold. As in this paper, if the spacer is manufactured by optimizing the injection hole and the temperature of the injection process based on simulation, it is expected that the spacer can be manufactured with high productivity.

KCI등재

5고출력 슁글드 모듈 제작을 위한 결정질 실리콘 태양전지 분할 셀의 전기적 특성

저자 : 노은빈 ( Eun Bin Noh ) , 배재성 ( Jae Sung Bae ) , 김정훈 ( Jung Hoon Kim ) , 유종현 ( Jong Hyun You ) , 이재형 ( Jaehyeong Lee )

발행기관 : 한국전기전자재료학회 간행물 : 전기전자재료학회논문지(J. Korean Inst. Electr. Electron. Mater. Eng.) 34권 6호 발행 연도 : 2021 페이지 : pp. 433-437 (5 pages)

다운로드

(기관인증 필요)

초록보기

As the demand for new and renewable energy increases due to the depletion of fossil fuels, solar power generation, a core energy source for new and renewable energy, requires research on solar modules for high output power generation. In this paper, the electrical characteristics of solar cell strip at the edge and in the center of single-crystal silicon having a semi-square shape were analyzed. The cell strip located in the center showed the efficiency increase by 0.26% compared to the cell strip at the edge of the solar cell. A shingled photovoltaic module was manufactured for each cell strip. As a result, the output power of the module using the cell strip located in the center was higher by 0.992%.

KCI등재

6YBa2Cu3O7-y 초전도 벌크의 중성자 조사 효과

저자 : 이상헌 ( Sang Heon Lee )

발행기관 : 한국전기전자재료학회 간행물 : 전기전자재료학회논문지(J. Korean Inst. Electr. Electron. Mater. Eng.) 34권 6호 발행 연도 : 2021 페이지 : pp. 438-441 (4 pages)

다운로드

(기관인증 필요)

초록보기

The electrical characteristics of single-crystal composite superconductors produced by a melting process were studied by neutron irradiation. In order to improve the current characteristics of the YBa2Cu3O7-y superconductor, it is necessary to form an effective flux pinning center inside the superconductor. In this study, an increase in flux pinning was attempted through neutron irradiation onto YBa2Cu3O7-y superconductors. The neutron irradiation was performed at 30 MeV for 500 sec, The electrical properties of the superconductors were measured in a magnetic field of 5 Tesla at 50 K using a magnetic properties measurement system (MPMS). After neutron irradiation, the critical current density of the YBa2Cu3O7-y superconductor in a 1 Tesla magnetic field was 1×105 A/㎠. Once neutrons were irradiated at 30 MeV and 10 μA for 500 sec, the critical current density was observed to increase significantly. When neutrons are irradiated to a superconductor, micro-defects are created in the superconductor, and they act as flux pinning centers that hold the magnetic field generated when an electric current flows.

KCI등재

7전기열량소자용 Ag 첨가량에 따른 K(Ta,Nb)O3 세라믹스의 구조적·전기적 특성

저자 : 이민성 ( Min-sung Lee ) , 박병준 ( Byeong-Jun Park ) , 임정은 ( Jeong-Eun Lim ) , 이삼행 ( Sam-haeng Lee ) , 이명규 ( Myung-gyu Lee ) , 박주석 ( Joo-Seok Park ) , 이성갑 ( Sung-gap Lee )

발행기관 : 한국전기전자재료학회 간행물 : 전기전자재료학회논문지(J. Korean Inst. Electr. Electron. Mater. Eng.) 34권 6호 발행 연도 : 2021 페이지 : pp. 442-448 (7 pages)

다운로드

(기관인증 필요)

초록보기

In this work, the (K1-xAgx)(Ta0.8Nb0.2)O3 (x=0.1-0.4) ceramics were fabricated using mixed-oxide method, and their structural and electrical properties were measured. All specimens represented a pseudo cubic structure with the lattice constant of 0.3989 nm. When 0.4 mol of Ag was added, second phases induced from metallic Ag and K2(Ta,Nb)6O16 phase were observed. Dielectric constant and dielectric loss of K(Ta0.8Nb0.2)O3 specimen doped with 0.3 mol of Ag were 2,737 and 0.446, respectively. The curie temperature was about -5℃, which does not change with Ag addition. The remanent polarization began to decrease sharply around 12~15℃, and the temperature at which the remanent polarization began to decrease as the applied voltage increased shifted to the high temperature side. The electrocaloric effect (ΔT) and electrocaloric efficiency (ΔT/ΔE) of the (K0.7Ag0.3)(Ta0.8Nb0.2)O3 ceramics were 0.01024℃ and 0.01825 KmV-1, respectively.

KCI등재

8고출력 슁글드 태양광 모듈 제작을 위한 스트링 연결에 관한 연구

저자 : 김주휘 ( Juhwi Kim ) , 김정훈 ( Junghoon Kim ) , 정채환 ( Chaehwan Jeong ) , 최원용 ( Wonyoung Choi ) , 이재형 ( Jaehyeong Lee )

발행기관 : 한국전기전자재료학회 간행물 : 전기전자재료학회논문지(J. Korean Inst. Electr. Electron. Mater. Eng.) 34권 6호 발행 연도 : 2021 페이지 : pp. 449-453 (5 pages)

다운로드

(기관인증 필요)

초록보기

Interest and investment in renewable energy have increased worldwide, highlighting the need for renewable energy. Solar energy was the most promising energy of all renewable energy sources, and it has the highest investment value. Because photovoltaics require a certain amount of area for installation, high density and high output performance are required. Shingled module is a promising technology in that they are featured by higher density and higher output compared to the conventional modules. Shingled technology uses a laser scribing to divide solar cells that are to be bonded with electrically conductive adhesive (ECA) to produce and connect strings, which has a higher output in the same area than the conventional modules. In the process of producing solar modules, metal ribbons are used to interconnect cells, but they are also needed for string connections in shingled solar cells. Accordingly, in this study, we researched the interconnection that best suits the connector that joins the string to the string. The module outputs produced under the conditions of the string interconnection were compared and analyzed.

KCI등재

9비카드뮴계 InZnP/ZnSe/ZnS 코어쉘 양자점의 발광 특성

저자 : 이영기 ( Young-ki Lee ) , 이민상 ( Min-Sang Lee ) , 이정미 ( Jeong-mi Lee ) , 원대희 ( Dae-Hee Won ) , 김종만 ( Jong-man Kim )

발행기관 : 한국전기전자재료학회 간행물 : 전기전자재료학회논문지(J. Korean Inst. Electr. Electron. Mater. Eng.) 34권 6호 발행 연도 : 2021 페이지 : pp. 454-460 (7 pages)

다운로드

(기관인증 필요)

초록보기

In this work, we synthesized alloy-core InZnP quantum dots, which are more efficient than single-core InP quantum dots, using a solution process method. The effect of synthesis conditions of alloy core on optical properties was investigated. We also investigated the conditions that make up the gradient shell to minimize defects caused by lattice mismatch between the InZnP core and ZnS is 7.7%. The stable synthesis temperature of the InZnP alloy core was 200℃. Quantum dots consisting of three layered ZnSe gradient shell and single layered ZnS exhibited the best optical property. The properties of quantum dots synthesized in 100 ml and in 2,000 ml flasks were almost equal.

KCI등재

10열확산 프로세스에 의한 초전도 벌크 합성

저자 : 이상헌 ( Sang Heon Lee )

발행기관 : 한국전기전자재료학회 간행물 : 전기전자재료학회논문지(J. Korean Inst. Electr. Electron. Mater. Eng.) 34권 6호 발행 연도 : 2021 페이지 : pp. 461-465 (5 pages)

다운로드

(기관인증 필요)

초록보기

A diffusion heat treatment process for YBa2Cu3O7-y bulk superconductor in a Gd2O3 powder was attempted. As a result of measuring the critical temperature of the superconducting bulk, there was no change in the superconducting transition temperature as the Gd particles diffused into the YBa2Cu3O7-y lattice, resulting in dense microstructure. As a result of measuring the critical current, the critical current density (Jc) of the superconducting bulk having treated by the Gd thermal diffusion treatment at 0 T increased to 3×104 A/㎠ at 0 T, which was higher than that of the superconducting bulk without thermal diffusion treatment. The surface magnetic force of the superconducting bulk with Gd thermal diffusion treatment was observed at the center of the superconducting bulk with the maximum trapped magnetic force (Hmax) of 1.51 kG. This result means that the Gd thermal diffusion treatment contributes to improving the critical current density Jc of YBa2Cu3O7-y, and it is believed that Gd particles migrating into the superconducting bulk through thermal diffusion either fill the surface pores of YBa2Cu3O7-y superconductors or act as a flux pinning center.

12
권호별 보기
같은 권호 다른 논문
| | | | 다운로드

KCI등재

1Bi0.5Na0.5TiO3-BiFeO3-SrTiO3 삼성분계 무연 압전 세라믹스의 강유전체-완화형 강유전체 상전이 거동

저자 : 이상섭 ( Sang Sub Lee ) , 이창헌 ( Chang-heon Lee ) , 즈엉짱안 ( Trang An Duong ) , 웬호앙티엔코이 ( Hoang Thien Khoi Nguyen ) , 한형수 ( Hyoung-su Han ) , 이재신 ( Jae-shin Lee )

발행기관 : 한국전기전자재료학회 간행물 : 전기전자재료학회논문지(J. Korean Inst. Electr. Electron. Mater. Eng.) 34권 1호 발행 연도 : 2021 페이지 : pp. 1-7 (7 pages)

다운로드

(기관인증 필요)

초록보기

This study investigated the structural, dielectric, ferroelectric, and strain properties of (0.98-x)Bi1/2Na1/2TiO3- 0.02BiFeO3-xSrTiO3 (BNT-BF-100xST, x=0.20, 0.22, 0.24, 0.26, and 0.28). All samples were successfully synthesized using the conventional solid-state reaction method and sintered at 1,175℃ for 2 h. The average grain size of the BNT-BF-100x ceramics decreased with increasing ST content. Furthermore, we observed that the ferroelectric- relaxor transition temperature (TF-R) decreased with increasing ST content, which eventually vanished in the BNT-BF-24ST ceramics. The results indicated that a ferroelectric to relaxor phase transition could be induced by ST modification. Consequently, a large electromechanical strain of 633 pm/V at 4 kV/mm was observed for the BNT-BF-26ST ceramics. These results imply that our materials have the competitive advantage of larger strain under lower operating field conditions compared with other BNT-based lead-free piezoelectric ceramics. We expect that BNT-BF-ST lead-free piezoelectric ceramics are promising candidates as a novel ternary BNT-based system and can find potential applications in actuators.

KCI등재

2Light Intensity 및 명암비 향상을 위한 마이크로 LED의 사파이어 기판 형상 변화 연구

저자 : 차유정 ( Yu-jung Cha ) , 곽준섭 ( Joon Seop Kwak )

발행기관 : 한국전기전자재료학회 간행물 : 전기전자재료학회논문지(J. Korean Inst. Electr. Electron. Mater. Eng.) 34권 1호 발행 연도 : 2021 페이지 : pp. 8-15 (8 pages)

다운로드

(기관인증 필요)

초록보기

Micro-LEDs can be applied to various parts of a product. However, it has disadvantages compared to general LEDs in large displays such as low efficiency, intensity, and contrast ratio, among others, owing to their short history of study. The simulations were carried out using ray-tracing software to investigate the change in light intensity and light distribution according to pattern shapes on the sapphire substrate of the flip-chip micro-LED (FC μ-LED) array. Three patterns-concave square patterns, convex square patterns, and Ag coated convex patterns-which existed on the opposite side of FC μ-LEDs (115 ㎛ × 115 ㎛) array, were applied. The intensity of FC μ-LEDs on the center of the receivers depends on the pattern depth with shape. The concave square patterns having FC μ-LEDs arrays show that decreasing intensity as the patterns depth. On the contrary, the convex square patterns having FC μ-LEDs arrays shows that increasing intensity as the patterns depth. In addition, the highest intensity shows that FC μ-LEDs having Ag-coated convex patterns on the opposite side of sapphire lead to a reduction in light crosstalk owing to the Ag film.

KCI등재

3DLC 박막이 코팅된 폴리머 애자의 표면 및 물리적 특성

저자 : 김영곤 ( Young Gon Kim ) , 박용섭 ( Yong Seob Park )

발행기관 : 한국전기전자재료학회 간행물 : 전기전자재료학회논문지(J. Korean Inst. Electr. Electron. Mater. Eng.) 34권 1호 발행 연도 : 2021 페이지 : pp. 16-20 (5 pages)

다운로드

(기관인증 필요)

초록보기

In this study, we tried finding new materials to improve the stain resistance properties of polymer insulating materials. Using the filtered vacuum arc source (FVAS) with a graphite target source, DLC thin films were deposited on silicon and polymer insulator substrates depending on their thickness to confirm the surface properties, physical properties, and structural properties of the thin films. Subsequently, the possibility of using a DLC thin film as a protective coating material for polymer insulators was confirmed. DLC thin films manufactured in accordance with the thickness of various thin films exhibited a very smooth and uniform surface. As the thin film thickness increased, the surface roughness value decreased and the contact angle value increased. In addition, the elastic modulus and hardness of the DLC thin film slightly increased, and the maximum values of elastic modulus and hardness were 214.5 GPa and 19.8 GPa, respectively. In addition, the DLC thin film showed a very low leakage current value, thereby exhibiting electrical insulation properties.

KCI등재

4포토 리소그래피 공정을 위한 Ti(10 nm)-Buffered층 위에 직접 성장된 고품질 무전사 단층 그래핀 공정

저자 : 오거룡 ( Keo-ryong Oh ) , 한이레 ( Yire-han ) , 엄지호 ( Ji-ho Eom ) , 윤순길 ( Soon-gil Yoon )

발행기관 : 한국전기전자재료학회 간행물 : 전기전자재료학회논문지(J. Korean Inst. Electr. Electron. Mater. Eng.) 34권 1호 발행 연도 : 2021 페이지 : pp. 21-26 (6 pages)

다운로드

(기관인증 필요)

초록보기

Single-layer graphene is grown directly on Ti-buffered SiO2 at 100℃. As a result of the AFM measurement of the Ti buffer layer, the roughness of approximately 0.2 nm has been improved. Moreover, the Raman measurement of graphene grown on it shows that the D/G intensity ratio is extremely small, approximately 0.01, and there are no defects. In addition, the 2D/G intensity ratio had a value of approximately 2.1 for single-layer graphene. The sheet resistance is also 89 Ω/□, demonstrating excellent characteristics. The problem was solved by using graphene and a lift-off patterning method. Low-temperature direct-grown graphene does not deteriorate after the patterning process and can be used for device and micro-patterning research.

KCI등재

5다층 그래핀/유리 구조체의 적외선 열복사 특성 연구

저자 : 박경아 ( Kyung-ah Park ) , 임미경 ( Mikyung Lim ) , 정현준 ( Hyun-june Jung ) , 김재현 ( Jae-hyun Kim )

발행기관 : 한국전기전자재료학회 간행물 : 전기전자재료학회논문지(J. Korean Inst. Electr. Electron. Mater. Eng.) 34권 1호 발행 연도 : 2021 페이지 : pp. 27-32 (6 pages)

다운로드

(기관인증 필요)

초록보기

In this study, we fabricated multilayer graphene on a glass substrate by stacking the monolayer graphene synthesized via chemical vapor deposition. The electrical sheet resistance and optical transmittance were evaluated to confirm the quality of the stacked multilayer graphene. Using the fabricated multilayer graphene/glass structure, we characterized its thermal radiative property in terms of the integrated emissivity. The integrated emissivity of the multilayer graphene/glass structure was tuned from 0.91 to 0.72 when the number of graphene layers was changed from 1 to 12. We also demonstrated that the emissivity tunability provided a way to control the apparent temperature of an object that can be used in infrared stealth applications.

KCI등재

6스퍼터링 질화탄소 박막의 트라이볼로지 및 전기적 특성의 기판 온도 영향

저자 : 박찬일 ( Chan Il Park )

발행기관 : 한국전기전자재료학회 간행물 : 전기전자재료학회논문지(J. Korean Inst. Electr. Electron. Mater. Eng.) 34권 1호 발행 연도 : 2021 페이지 : pp. 33-38 (6 pages)

다운로드

(기관인증 필요)

초록보기

Using facing target magnetron sputtering (FTMS) with a graphite target source, carbon nitride thin films were deposited on silicon and glass substrates at different substrate temperatures to confirm the tribological, electrical, and structural properties of thin films. The substrate temperatures were room temperature, 150℃, and 300℃. The tribology and electrical properties of the carbon nitride thin films were measured as the substrate temperature increased, and a study on the relation between these results and structural properties was conducted. The results show that the increase in the substrate temperature during the fabrication of the carbon nitride thin films increased the hardness and elastic modulus values, the critical load value was increased, and the residual stress value was reduced. Moreover, the increase in the substrate temperature during thin-film deposition was attributed to the improvement in the electrical properties of carbon nitride thin film.

KCI등재

7태양전지 응용을 위한 ZnO:Al 박막의 전기적·물리적 특성에서 증착 온도의 영향

저자 : 박찬일 ( Chan Il Park )

발행기관 : 한국전기전자재료학회 간행물 : 전기전자재료학회논문지(J. Korean Inst. Electr. Electron. Mater. Eng.) 34권 1호 발행 연도 : 2021 페이지 : pp. 39-43 (5 pages)

다운로드

(기관인증 필요)

초록보기

In the case of ZnO:Al thin films, it is the best material that can replace ITO that is mainly used as a transparent electrode in electronic devices such as solar cells and flat-panel displays. In this study, ZnO:Al films were fabricated by using the RF dual magnetron sputtering method at various substrate temperatures. As the substrate temperature increased, the crystallinity of the ZnO:Al thin films was improved, and the electrical conductivity and electrical properties of the thin film improved owing to the increase in grain size. In addition, the surface roughness of the ZnO:Al thin films increased due to changes in the surface and density of the thin films. Moreover, the substrate temperature increased the density of thin films and improved their transmittance. To be applied to solar cells and other several electronic devices in the future, the hardness and adhesion properties of the thin film improve as the substrate temperature increases.

KCI등재

8다파장 IR과 NIR 모듈의 평균 수명 예측에 관한 연구

저자 : 김동표 ( Dong Pyo Kim ) , 김경섭 ( Kyung Seob Kim )

발행기관 : 한국전기전자재료학회 간행물 : 전기전자재료학회논문지(J. Korean Inst. Electr. Electron. Mater. Eng.) 34권 1호 발행 연도 : 2021 페이지 : pp. 44-49 (6 pages)

다운로드

(기관인증 필요)

초록보기

Recently, infrared (IR) and near-infrared (NIR) light-emitting diodes (LEDs) were widely used for home medical applications owing to its low output power and wide exposed area for curing. For deep penetration of the light under the skin, multiple LEDs with wavelengths of 700~10,000 nm were located on a flexible printed circuit board. When multiple wavelengths of LEDs were soldered on a circuit board, the lifetime of LED module highly depends on LEDs with a short lifetime. The mean time to failure (MTTF) was able to calculate with the experimental results under high temperature and the Arrhenius model. The results of this study could help companies to approve the warranty of LED modules and its product.

KCI등재

9진공인터럽터용 신규 접점소재에 대한 차단 성능 평가

저자 : 차영광 ( Young-kwang Cha ) , 이일회 ( Il-hoi Lee ) , 주흥진 ( Heung-jin Ju ) , 신태용 ( Tae-yong Shin ) , 박경태 ( Kyong-tae Park )

발행기관 : 한국전기전자재료학회 간행물 : 전기전자재료학회논문지(J. Korean Inst. Electr. Electron. Mater. Eng.) 34권 1호 발행 연도 : 2021 페이지 : pp. 50-55 (6 pages)

다운로드

(기관인증 필요)

초록보기

Copper-chromium alloys have been used as contact materials of vacuum interrupters in circuit breakers, but new materials with highly stable performance are required to break the high voltage and high current barrier due to the recent increase in breaking capacity. In this paper, a new contact material was fabricated from a ternary alloy instead of existing Cu-Cr alloys. Its breaking performance and endurance were verified from a synthetic test and compared with that of various contact materials. The test results verified that the breaking performance of the new contact material was excellent.

KCI등재

10촉매법을 적용한 오존 저감형 플라즈마 기기

저자 : 전신영 ( Sin Young Jeon ) , 김동준 ( Dong Jun Kim ) , 김종엽 ( Jong Yeop Kim ) , 권진구 ( Jin Gu Gwon ) , 전용민 ( Young Min Jeon ) , 도계령 ( Gye Ryung Do ) , 이성의 ( Seong Eui Lee )

발행기관 : 한국전기전자재료학회 간행물 : 전기전자재료학회논문지(J. Korean Inst. Electr. Electron. Mater. Eng.) 34권 1호 발행 연도 : 2021 페이지 : pp. 56-62 (7 pages)

다운로드

(기관인증 필요)

초록보기

In this study, we created a DBD plasma device and a MnO2 catalyst mesh filter for evaluating ozone reduction of devices via the catalyst method. The DBD plasma device was manufactured by applying MnO2 paste to soda lime glass via the screen-printing method. The MnO2 catalyst mesh filter was manufactured by mixing MnO2 powder with binder with a 10% difference in concentration from 10% to 50% and then applying it using the dip-coating method. Finally, we sintered a MnO2 catalyst mesh filter in an electric furnace. We evaluated the characteristics of ozone generation according to the MnO2 gas flow of DBD plasma devices, the opening ratio, and ozone reduction performance of the MnO2 catalyst filters. Ozone reduction performance was approximately 20.4% at MnO210 wt%, 37.8% at MnO2 30 wt% and 50% at MnO2 50 wt%.

12
발행기관 최신논문
자료제공: 네이버학술정보
발행기관 최신논문
자료제공: 네이버학술정보

내가 찾은 최근 검색어

최근 열람 자료

맞춤 논문

보관함

내 보관함
공유한 보관함

1:1문의

닫기